Electric Current Conversion Calculator

Convert amps, milliamps, microamps and 33 other current units. See the conversion factor and use the worked examples to calculate current, power and battery run time.

Notebook illustration of a digital ammeter displaying 300 milliamps
300mA=0.3A

Electric Current Converter

1A=1,000mA
Multiplier 1,000

Compare results in all 36 units
Convert through amperes. Multiply by the source unit’s ampere factor and divide by the target unit’s ampere factor.Ito=Ifromffromfto

How to convert electric current

  1. 1
    Enter the current

    Use a positive or negative number, decimal or scientific notation. For 3.5×10−3 amperes, enter 3.5e-3.

  2. 2
    Choose the source unit

    Use the unit from your measurement. SI amperes, equivalent SI forms and historical units have separate groups.

  3. 3
    Choose the target unit

    The result and multiplier update as soon as you change either unit.

  4. 4
    Try a shortcut or swap

    The buttons below the result select common unit pairs. Swap reverses the units and keeps the original number.

  5. 5
    Compare or copy

    Expand the comparison to see the current in all 36 units, or copy the selected conversion.

Electric current conversion factors

Current units and their ampere equivalents
UnitSymbolConversion to amperesContext
QuectoampereqA1qA=10−30ASI amperes
RontoampererA1rA=10−27ASI amperes
YoctoampereyA1yA=10−24ASI amperes
ZeptoamperezA1zA=10−21ASI amperes
AttoampereaA1aA=10−18ASI amperes
FemtoamperefA1fA=10−15ASI amperes
PicoamperepA1pA=10−12ADevice leakage and sensitive lab measurements
NanoamperenA1nA=10−9ADiode leakage and amplifier input bias
MicroampereμA1μA=10−6ALow-power electronics and sensor currents
MilliamperemA1mA=10−3ALEDs, sensors and charging
CentiamperecA1cA=10−2ASI amperes
DeciamperedA1dA=10−1ASI amperes
AmpereA1A=1ASI base unit
DecaamperedaA1daA=101ASI amperes
HectoamperehA1hA=102ASI amperes
KiloamperekA1kA=103AHigh-current power equipment and fault ratings
MegaampereMA1MA=106AHigh-current plasma experiments
GigaampereGA1GA=109ASI amperes
TeraampereTA1TA=1012ASI amperes
PetaamperePA1PA=1015ASI amperes
ExaampereEA1EA=1018ASI amperes
ZettaampereZA1ZA=1021ASI amperes
YottaampereYA1YA=1024ASI amperes
RonnaampereRA1RA=1027ASI amperes
QuettaampereQA1QA=1030ASI amperes
Coulomb per secondCs1Cs=1AEquivalent SI forms
Siemens voltS·V1S·V=1AEquivalent SI forms
Volt per ohmVΩ1VΩ=1AEquivalent SI forms
Watt per voltWV1WV=1AEquivalent SI forms
Weber per henryWbH1WbH=1AEquivalent SI forms
Abampere (biot)abA1abA=10AAlso called the biot
CGS electromagnetic unit of currentemu current1emu current=10ALegacy units
StatamperestatA1statA≈3.335641×10−10AAlso called the CGS electrostatic unit of current
CGS electrostatic unit of currentesu current1esu current≈3.335641×10−10ALegacy units
Franklin per secondFrs1Frs≈3.335641×10−10ALegacy units
Gilbert (one-turn current equivalent)Gi1Gi=104πASingle-turn current equivalent. The gilbert measures magnetomotive force.

What electric current measures

Electric current measures how quickly charge passes a point. Engineers describe tiny sensor currents in picoamperes, appliance currents in amperes and large electrical fault currents in kiloamperes. The ampere, named after André-Marie Ampère, is one of seven SI base units.

Since the 2019 SI revision, the elementary charge is fixed at e=1.602176634×10−19C exactly. A coulomb is equivalent in magnitude to about 6.241509074×1018 elementary charges.

Average and instantaneous current

Iavg=ΔQΔti(t)=dQdt1A=1Cs

Current is measured in amperes, charge in coulombs and time in seconds.

ΔQ is the net charge that passes during the time interval Δt. Use the first equation for an average over a finite interval and the derivative for the current at a particular instant. The sign refers to the chosen direction.

Calculate current with Ohm’s law

Georg Simon Ohm identified the relationship between voltage and current. For an ohmic component with fixed resistance, use the voltage across that component and its resistance to calculate the current through it.

Three forms of Ohm’s law

I=VRV=IRR=VI

Use amperes for current, volts for voltage and ohms for resistance.

Example 1. Estimate LED current from the resistor’s voltage drop

An LED and a 220Ω resistor are in series across a 5.0V supply. Assume the LED’s forward drop is 2.0V.

VR=5.0V−2.0V=3.0VI=VRR=3.0V220Ω≈13.6mA

The estimate is 13.6mA. Using all 5.0V across the resistor gives 22.7mA, which models the resistor by itself.

Power, current and voltage

Power P is the rate of energy transfer. In a DC circuit, use voltage and current for the same load. The expressions involving R follow from Ohm’s law for a resistor. Use the power converter to switch between watts and kilowatts before calculating.

Power and current for a DC load

P=VII=PVP=I2R=V2R|I|=PR

The second line applies to a resistor. Power is measured in watts.

Example 2. Find the output current of a laptop charger

The charger can deliver 65W at 20V DC.

I=PV=65W20V=3.25A

That is the output current at full load. The charger’s mains input current depends on its efficiency and AC characteristics.

Example 3. Find heat dissipated by a resistor

A 100Ω resistor carries 50mA=0.050A.

P=I2R=(0.050A)2(100Ω)=0.25W

The resistor dissipates 250mW.

SI prefixes from quecto to quetta

SI prefixes change the size of the ampere by a power of ten. Symbols are case-sensitive. The lowercase m in mA means milli, and the uppercase M in MA means mega. In text entry, uA is a common substitute for μA.

Use picoamps and nanoamps for small leakage and bias currents, microamps for low-power electronics, and milliamps for LED and sensor currents. Household loads and breaker ratings typically use amps. Electrical fault ratings, welding and lightning may reach hundreds of amps or more, and high-current plasma experiments may reach megaamps.

Charge, current and battery run time

Ampere-hours and milliampere-hours measure charge. At a constant current, one ampere flowing for one second transfers one coulomb. At an average current, multiplying by the elapsed time gives total net charge.

Charge and ideal battery run time

Q=Iavgt1Ah=3,600C1mAh=3.6Ct=QusableIavg

Use charge in mAh and current in mA to get time in hours.

Example 4. Estimate phone battery run time

Assume a battery has 4,500mAh of usable charge and the phone draws 180mA on average.

t=4,500mAh180mA=25h

Real run time depends on battery age, temperature, the phone’s cutoff voltage and how the load changes.

Kirchhoff’s current law

Gustav Kirchhoff’s current law applies conservation of charge to a circuit junction. Choose one sign for currents entering and the opposite for currents leaving. At an ideal junction where charge does not accumulate, the signed currents sum to zero.

Conservation of charge at a junction

∑kIk=0∑Iin=∑Iout

In the second line, each sum uses positive current magnitudes.

For example, if 5mA enters a junction and 2mA leaves on one branch, 3mA leaves on the other. This is the basis of nodal analysis. Kirchhoff’s voltage law provides a separate constraint for loops.

AC current, RMS and peak values

Alternating current reverses direction. Grid supplies are usually close to sinusoidal, with nominal frequencies of 50 Hz in most of Europe and 60 Hz in the United States. Other sources, such as inverters and electronic loads, can produce different waveforms.

Sinusoidal alternating current

i(t)=Ipeaksin(2πft+ϕ)

Ipeak is the peak current, f is frequency in hertz and ϕ is phase in radians.

RMS stands for root mean square. A current’s RMS value is the steady DC current that would deliver the same average power to a resistor. Use the sine-wave shortcut only for a pure sinusoid with no DC offset. For a different periodic waveform, use the mean square over a period or a suitable true-RMS instrument.

Convert RMS and peak values for a sine wave

IRMS=Ipeak2≈0.7071IpeakVpeak=(230V)2≈325V

The voltage example uses a nominal 230-volt RMS mains supply.

Example 5. Find RMS and peak current for a resistive heater

A 2kW resistive heater runs on a sinusoidal 230V RMS supply.

IRMS=2,000W230V≈8.70AIpeak=2IRMS≈12.3A

These are the calculated currents for the stated load and supply.

Abamperes, statamperes and gilberts

Older references may use centimetre–gram–second units. In the CGS electromagnetic system, the abampere or biot is exactly 10A, based on the historical force between parallel current-carrying wires. In the CGS electrostatic system, a statampere is one statcoulomb per second, also called one franklin per second. Its factor in amperes is rounded to the precision shown in the table.

The gilbert measures magnetomotive force. One gilbert is 104π ampere-turns. In a single-turn model, that corresponds to about 0.795775A. For multiple turns, divide the ampere-turn value by the number of turns.

What affects the severity of an electric shock?

Electric shock severity depends on the magnitude of the current through the body, its path, the time in contact and the waveform. Voltage, the source and contact conditions affect how much current may flow. A value in milliamps alone cannot establish a safe exposure.

Possible effects of electric shock
EffectWhat can happen
Tingling or painSensation varies with current and contact. A mild sensation is an unreliable guide to severity.
Muscle contractionInvoluntary contraction can cause loss of control or make releasing a live conductor difficult.
Breathing difficultyCurrent through the chest can interfere with breathing muscles.
Abnormal heart rhythmA shock can disrupt the heart’s rhythm, including causing ventricular fibrillation.
BurnsElectrical injury can extend beneath the skin. Arcs can also cause thermal burns.
Falls and impact injuriesInvoluntary movement or a startle response can cause a fall or collision.
Work on de-energised equipment. Follow applicable electrical safety procedures. The NIOSH manual explains de-energisation, protective equipment and ground-fault protection.

How much current do common devices draw?

Typical and example electric currents
DeviceCurrentConditions
Single LED10 to 30mAIllustrative forward current for many indicator LEDs. Check the component datasheet.
Bluetooth Low Energy device1 to 15mAIllustrative active current for a low-power radio. Sleep current can be much lower.
Arduino board40 to 50mAExample active board current before peripherals. The board model and operating mode matter.
USB 2.0 portUp to 500mAFor a configured high-power device on a standard legacy USB 2.0 port.
Smartphone charging1 to 5AIllustrative charger output range. The charging protocol and cable determine the available current.
Laptop charger3.25AExample for a 65W charger supplying 20V DC.
Household kettle (UK)8.7 to 13AApproximate RMS current for a 2 to 3kW resistive load at 230V.
EV AC Level 2 charging16 to 48AExample installations. At 240V, these correspond to 3.84 through 11.52kW at unity power factor.
EV DC fast charging375AExample for 150kW at 400V. Actual current changes with voltage and the charging session.
Arc welding50 to 500AIllustrative arc current range. The process, electrode and workpiece affect the setting.
Lightning return strokeAbout 30kA peakNWS gives this as a typical first return-stroke peak. Individual discharges vary widely.
N
NUM8ERS Editorial TeamUpdated November 2026. Measurement and reference sources are listed below.

Frequently asked questions

What is electric current and how is it defined?
Current is the rate at which electric charge passes a point. Average current is Iavg=ΔQΔt. The SI unit is the ampere. The SI fixes the elementary charge at e=1.602176634×10−19C.
How do I convert amps to milliamps?
Multiply the number of amps by 1,000. For example, 0.5A=500mA, since 1mA=10−3A.
How do I convert milliamps to amps?
Divide the number of milliamps by 1,000. For example, 250mA=2501,000A=0.25A.
How do I convert microamps to milliamps?
Divide microamps by 1,000 to get milliamps. For example, 5,000μA=5mA. One microamp equals 10−6A.
What is the formula for current using Ohm's Law?
Use I=VR for an ohmic component. For DC power, I=PV when voltage and power refer to the same load. For a resistor, the current magnitude also follows from |I|=PR.
What is the unit coulomb per second?
One coulomb per second is exactly one ampere: 1Cs=1A. The current measures how much charge passes per second.
What is an abampere?
The abampere, or biot, was used in the CGS electromagnetic system. 1abA=10A. This unit appears in older references based on forces between current-carrying wires.
What is a statampere?
The statampere is the CGS electrostatic current unit. It equals one statcoulomb per second. NIST gives 1statA≈3.335641×10−10A.
How much current is dangerous to humans?
A shock can affect breathing, heart rhythm and muscle control. The risk depends on the current path, time in contact, waveform and other conditions as well as current magnitude.
What is RMS current and how is it calculated?
RMS current gives the equivalent DC heating in a resistor. For a pure sine wave, IRMS=Ipeak2. The peak-to-RMS factor varies with the waveform.
What is Kirchhoff's Current Law and why does it matter?
For an ideal junction, ∑Iin=∑Iout. Use measured or known branch currents to solve for an unknown current at that node.
How is current related to battery capacity (mAh)?
Capacity in mAh measures charge. Divide usable capacity by the average current in milliamps to estimate hours. For example, t=3,000mAh150mA=20h.
What is the difference between AC and DC current?
Direct current has one direction and can vary in magnitude. Alternating current periodically reverses direction. Both are measured in amperes. An AC reading may be RMS or peak depending on the instrument and what it reports.
What current does a USB charger supply?
A configured high-power USB 2.0 device can draw up to 500mA on a standard port, and the comparable USB 3.x figure is 900mA. USB Battery Charging 1.2 can support 1.5A. Compatible USB-C Power Delivery can reach 5A, including 100W at 20V and up to 240W at 48V with appropriate hardware. For proprietary charging modes such as Quick Charge, check the charger, device and cable specifications.
How accurate is the Num8ers Electric Current Converter?
SI prefix factors are exact powers of ten. The converter displays up to 10 significant digits using browser floating-point arithmetic. The statampere and equivalent legacy factors are rounded to the precision given by NIST.
Have a current value from a meter or a datasheet? Convert it above and expand the comparison to see which unit is easiest to read. For feedback about the tool, contact NUM8ERS.

Sources and standards